Price:
$5775
Product ID:
DES-ACHX6-361836
Lead Time:
Contact Us to inquire about lead times
Return Policy:
14 days for a full refund

Product Specifications

Inside Dimensions (inch):
36 W X 18 D X 36 H
Product Dimensions (inch):
40 W X 24 D X 40 H
Tolerance (inch):
+/- 0.125
Chamber Material:
Clear Cast Acrylic
Lid Material:
Clear Cast Acrylic
Door Seal:
Air Tight (Buna-N O-Ring)
Hygrometer Accuracy :
+/- 5%RH
Thermometer Accuracy :
+/- 1% Deg C

Features

Clear Acrylic Desiccator Cabinet
1 perforated shelf per box
1 gas IN port 1/4 NPT (blanked off) per box
1 gas OUT port 1/4 NPT (blanked off) per box
digital hygrometer per box
digital thermometer per box
dry, dust-free, and oil-free environment

Description

There is a total of six (6) desiccator boxes in this system ? the boxes are arranged in three rows and two columns (3x2 cofiguration), bringing the summarized dimensions to 24-inch-wide, 12-inch-deep by 36 inch high. Each single desiccator box has the inside dimensions of 12-inch Wide, 12-inch Deep, and 12-inch High. All three desiccators are fully assembled and are ready to go. Each comes with one fully removable perforated shelf, a digital hygrometer, two gas ports that are 1/4 inch NPT and plugged, and four door clamps. These are air tight boxes which means that as soon as you close the door and engage the clamps, they become hermetically sealed.

We construct our desiccator cabinets the same way we construct any of our products which means that these desiccator boxes are robustly designed and quality manufactured to consistently perform and meet your needs. These two dry boxes will enable you to store any component that requires dry storage such as anhydrous and hygroscopic biological, chemical compound, or electronic assemblies. These can be used for long term and short-term storage of laboratory samples as well. Desiccator cabinets will reduce humidity/oxygen within the box. Desiccators are air tight containers envisioned to store samples shielded from dust and contamination and/or in a low humidity and in some cases a low oxygen environment.

Please note that this desiccator is not intended to be pressurized, if you required a vacuum chamber or a pressure chamber click on the link. Also note that acrylic material is hygroscopic meaning that it will absorb and transport humidity. Say you are operating in a relatively high humidity environment (80%) and say that you bring the humidity inside this desiccator cabinet to below 20%. Due to the nature of acrylic, the humidity will travel through the walls and slowly increase the humidity until it gets to a steady state. If no further action is taken, the humidity inside the desiccator cabinet will equalize with the outside within a couple of hours. In order to keep the humidity at a certain level, you will have to monitor it or control it as we mentioned before, acrylic is hygroscopic.

You may be interested in some of our other items

We treat our customers well by Over-Delivering on our Promises (reason why we are Highly Rated on Google My Business). Check out some of our other items we carry that you can combine/integrate with your systems or projects.

Internal Pressurization ASTM F2096 Leak Testing Systems
Internal Pressurization (ASTM F2096) Leak Testing Systems are instruments that are used during the Quality Control process to discover leaks in sealed packages. As opposed to the vacuum bubble leak test, where the specimen is subjected to a vacuum, the internal pressurization integrity test creates a pressure difference and drives the air through a leak by internally pressurizing the specimen. Our Internal Pressurization Leak Testing Systems are designed and built to conform to the ASTM F2096 Protocol Standard.
Roots Blower Vacuum Pumps
Roots Blower Vacuum Pumps are used when a large amount of Volumetric Airflow is Required. Root Vacuum Pumps cannot operate independently and must be used in conjunction with another roughing pump such as Rotary Vane Pump or Piston Pump. The advantages of a Roots Vacuum Pump is that the Pumping Speed can be increased by a factor of 5 up to a factor of 10; meaning that a 20 CFM Rotary Vane Vacuum Pump can now be boosted to pump 120 CFM!
Our Work: Chamber for Vacuum Extrusion System
This is a custom acrylic vacuum chamber build for a high volume manufacturer of parts which are fabricated using vacuum extrusion techniques. The challenge was to build a vacuum chamber system which mated on two perpendicular surfaces; on the bottom and on the rear of the chamber. This was accomplished by incorporating a double gasket mechanism on the bottom and incorporating a clamping mechanism on the rear.
Related Articles: Piston Vacuum Pump: The Ultimate Guide to WOB-L and ROC-R Vacuum Pumps
This article is intended to be the Definitive Resource when it comes to Piston Vacuum Pumps. We know a thing or two about vacuum pumps because we work with them every day. In this article we will specifically talk about Piston Vacuum Pumps – the WOB-L and the ROC-R to be exact.

Additional Comments

1. Depiction: We go above and beyond to represent our products the best we can, but all images are for reference only. If you want the exact dimensions of a product, please refer to the product drawing. If the drawing is not present, please contact us.

2. Discount: If you are ordering more than one item you will qualify for a discount, contact us for more details. No discount will be given after you have ordered and then realized you can get a discount. We put in a lot of effort writing this and we don`t reward failure to read our descriptions. However, since we are nice guys, we will give you a discount on your next order.

3. Shipping: The shipping rates are for the lower 48 states only; additional shipping charges apply to Alaska, Hawaii, and international orders. Keep in mind that international order will also be subject to duty and other charges.

4. Products: Our products are built-to-order; therefore, your product can be customized, but you must let us know beforehand. The pricing, shipping terms, and lead time apply to orders of less than three (3) items. If you are ordering more than 3 items, you should contact us to discuss your quote.

5. Return Policy: 14 days on all standard products. We stand 100% behind our products. If there was a mistake on our part, you will be refunded 100% of your money including shipping. If the mistake was on your part or you decided that you didn`t want it after all, you will pay for shipping and we will fully refund rest of your money. Chamber must be insured during return shipping for the price that you paid for and in a non-damaged condition. Return Policy does NOT apply to custom items, jobs, or products. If you have asked us to modify any of our standard products, you will not be able to return your item.